8/31/2023 0 Comments Replacing glass shower door sweepOnce difference when ordering this replacement compared to the original one provided by the manufacturer is the small details. But of me as the homeowner, that's a minor detail that can be overlooked. DIY TakeawaysĪll in all, in the picture, you can notice where the sweep is semi-cracked. If its tough, avoid cuts by using a towel at the end to apply more pressure. I suggest opening the door as wide as possible so you can vertically snap the door seal to the shower door. Make sure the drip guard is inside the shower. Lastly, install the bottom door sweep to the cleaned shower door. I did lose some of the plastic, but it's purely cosmetic. I ended up cutting a deep notch, then gently snapping the rest off. The plastic was much tougher than I was expecting, so cutting the seal to length took more effort than I was expecting. But if you cut it too short, there'll be a small gap where water could bypass the seal. If it's too long, your shower door won't close. I'd suggest wearing gloves if you suspect it's mold to avoid getting it under your fingernails.Ĭut the replacement shower door bottom seal to length. Now would also be a good time to clean the glass if you notice any mold. It's attached by the tension of the plastic. Once your shower door bottom seal arrives, simply pull off the existing piece. Specifically, it's the Butecare Frameless Shower Door Bottom Seal 3/8" x 39", but find one that works best for your shower door. However, I did end up ordering one that was nearly half the price (got two replacement pieces for the price of one) of similar items, even when compared across different websites, plus was highly reviewed. Unfortunately for me, I wasn't able to find one that exactly matched my specifications. Since many of the frameless shower glass doors are customized, the horizontal door length may be different in every case. Since this length is much longer, using a tape measurer will make this process much simpler. Next, you'll need to measure the horizontal length of the shower door. If you don't have one, a simple ruler should do the trick. Before you order, it's a good idea to confirm the thickness of the shower glass door by measuring with a tape measurer. Because of this, the frame-less shower glass is thicker at 3/8". That means there are no metal bars above or on the sides that support the glass. In my case, we have a frameless shower enclosure. Simply snap off the existing shower door seal, do a bit of cleaning, and snap on the new shower door seal. And it turns out, it's the easiest DIY project, involving almost no tools. Afraid that it more than accumulated dirt and that it could be mold, I decided it was time to replace it. Despite our efforts in keeping the glass clean with periodic cleaning of the water stains off the glass and removing mildew on the grout between the shower tiles, the sweep at the bottom of the shower door that creates a seal to prevent water from splashing out of the shower slowly turned darker and darker. It's the bathroom, and specifically the shower we use daily each and every morning. We love our frameless shower enclosure in our master bathroom. If there is still water on the floor, you may need to add more caulking around the shower door to remove any leaks.The links in this post contain affiliate links and I will receive a small commission if you make a purchase after clicking on my link. Afterward, assess the condition of the floor. Test the new door sweep by taking a shower (or running it against the door). If the door sweep is designed to fit in the track, the edge of the sweep should be coated lightly with petroleum jelly. It is now time to install the new door sweep in the track. Using the old door sweep as a pattern, cut the new door sweep to the same length as the old one. There is a slight variation in size for various kinds of door sweeps, so taking the old one with you is the best way to avoid a wasted trip and unnecessary returns. This will help ensure that you get a new one that matches the size and height of the existing sweep. Take the old door sweep with you to your local hardware store or home improvement center. Depending on the type of door sweep that is currently in use, it may be necessary to unscrew the door sweep from the track. Step 2Ĭarefully grasp the edge of the door sweep, pulling it towards the outside of the door until the strip has come loose from the track. Open the shower door from the inside and leave it propped open.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |